Hornady 180XTP 357 Magnum
-
- Posts: 42
- Joined: 12 Oct 2021 03:19
- Location: Virginia
- Has thanked: 6 times
- Been thanked: 7 times
Hornady 180XTP 357 Magnum
Few things I've learned and few things I need advice on.
Started with twenty rounds.
Flared the brass . This took 5 (spare) pieces of brass before I figured out what not to do.
How deep is the flare supposed to be?
Am I correct in saying - just deep enough to lightly insert the base of the bullet into the brass.
Used 11.6 Grains of H110. For a total of 10 rounds.
Used 12.9 Grains of H110 . For a total of 10 rounds.
Double checked the accuracy of my digital scale multiple times and checked powder charge twice as a precaution.
When seating the bullet what matters most the maximum or minimum COAL. Every round was just under max published COAL
Max published COAL was 1.59 respectively.
Every loaded round was ranging between 1.55 and 1.587 on the high end.
Any tips for getting these dimensions closer together?
Each round cycled well through my Rossi and fit well in my SP101.
Being as this is my first time you loading, having done all the safety checks I could. What would you recommend I test these rounds through...Revolver or Rossi 92.
What would be the safest bet. Both guns are very strongly built.
I am confident I did everything right. But that needs to be confirmed through firing?
Started with twenty rounds.
Flared the brass . This took 5 (spare) pieces of brass before I figured out what not to do.
How deep is the flare supposed to be?
Am I correct in saying - just deep enough to lightly insert the base of the bullet into the brass.
Used 11.6 Grains of H110. For a total of 10 rounds.
Used 12.9 Grains of H110 . For a total of 10 rounds.
Double checked the accuracy of my digital scale multiple times and checked powder charge twice as a precaution.
When seating the bullet what matters most the maximum or minimum COAL. Every round was just under max published COAL
Max published COAL was 1.59 respectively.
Every loaded round was ranging between 1.55 and 1.587 on the high end.
Any tips for getting these dimensions closer together?
Each round cycled well through my Rossi and fit well in my SP101.
Being as this is my first time you loading, having done all the safety checks I could. What would you recommend I test these rounds through...Revolver or Rossi 92.
What would be the safest bet. Both guns are very strongly built.
I am confident I did everything right. But that needs to be confirmed through firing?
-
- Posts: 120
- Joined: 28 May 2021 15:28
- Location: PA
- Has thanked: 2 times
- Been thanked: 9 times
Re: Hornady 180XTP 357 Magnum
Try in both weapons. 5 in the rifle and 5 in the revolver. Sounds like you have done every thing right.
I use cast bullets in my rossi 92.. good luck,post your results.. johnny
I use cast bullets in my rossi 92.. good luck,post your results.. johnny
- GasGuzzler
- Moderator
- Posts: 2757
- Joined: 02 Nov 2015 19:54
- Location: Cooke County, TX
- Has thanked: 310 times
- Been thanked: 453 times
Re: Hornady 180XTP 357 Magnum
Jacketed bullets don't need much flare at all. If you can see the flare with the naked eye, it's probably too much for JHP's.
__________________________________________________________________________________________
I've always been crazy but it's kept me from going insane.
I've always been crazy but it's kept me from going insane.
-
- Posts: 42
- Joined: 12 Oct 2021 03:19
- Location: Virginia
- Has thanked: 6 times
- Been thanked: 7 times
Re: Hornady 180XTP 357 Magnum
So a slight flare should be adequate.GasGuzzler wrote: ↑03 Mar 2024 07:57 Jacketed bullets don't need much flare at all. If you can see the flare with the naked eye, it's probably too much for JHP's.
What is the difference between jacketed and lead as far as flaring goes?
-
- Posts: 42
- Joined: 12 Oct 2021 03:19
- Location: Virginia
- Has thanked: 6 times
- Been thanked: 7 times
- GasGuzzler
- Moderator
- Posts: 2757
- Joined: 02 Nov 2015 19:54
- Location: Cooke County, TX
- Has thanked: 310 times
- Been thanked: 453 times
Re: Hornady 180XTP 357 Magnum
Lead bullets are generally slightly larger in diameter. They also can shave if the brass is not sized or flared properly.
__________________________________________________________________________________________
I've always been crazy but it's kept me from going insane.
I've always been crazy but it's kept me from going insane.
-
- Posts: 42
- Joined: 12 Oct 2021 03:19
- Location: Virginia
- Has thanked: 6 times
- Been thanked: 7 times
Re: Hornady 180XTP 357 Magnum
I got ya. For lead bullets with multiple lands; where do you normally crip-seat at?GasGuzzler wrote: ↑04 Mar 2024 07:35 Lead bullets are generally slightly larger in diameter. They also can shave if the brass is not sized or flared properly.
- GasGuzzler
- Moderator
- Posts: 2757
- Joined: 02 Nov 2015 19:54
- Location: Cooke County, TX
- Has thanked: 310 times
- Been thanked: 453 times
Re: Hornady 180XTP 357 Magnum
I think you are referring to crimp grooves and there's not enough information in the question to answer that. Crimp grooves are the last consideration I have when loading lead bullets. Also, most molds make bullets with only one crimp groove anyway. The others are lube grooves most times.
I do have a NOE mold with one lube groove and two crimp grooves though.
Bullet length and weight, case volume, type of powder, gun's chamber are all more important on the OAL than where the mold maker put the crimp groove.
__________________________________________________________________________________________
I've always been crazy but it's kept me from going insane.
I've always been crazy but it's kept me from going insane.
-
- Posts: 42
- Joined: 12 Oct 2021 03:19
- Location: Virginia
- Has thanked: 6 times
- Been thanked: 7 times
Re: Hornady 180XTP 357 Magnum
Yes crimp groves is what I was referring to.GasGuzzler wrote: ↑06 Mar 2024 06:52I think you are referring to crimp grooves and there's not enough information in the question to answer that. Crimp grooves are the last consideration I have when loading lead bullets. Also, most molds make bullets with only one crimp groove anyway. The others are lube grooves most times.
I do have a NOE mold with one lube groove and two crimp grooves though.
Bullet length and weight, case volume, type of powder, gun's chamber are all more important on the OAL than where the mold maker put the crimp groove.
And the information above is much appreciated. Thanks for the input.
-
- Posts: 42
- Joined: 12 Oct 2021 03:19
- Location: Virginia
- Has thanked: 6 times
- Been thanked: 7 times
Re: Hornady 180XTP 357 Magnum
Any thoughts on if I need to add crimp?
How do you know what is an adequate crimp on 357 magnum ammo?
How do you know what is an adequate crimp on 357 magnum ammo?
You do not have the required permissions to view the files attached to this post.