can we discuss blowback?

The Rossi Model R92, a lightweight carbine for Cowboy Action, hunting, or plinking! Includes Rossi manufactured Interarms, Navy Arms, and Puma trade names.
Post Reply
stevep1954
Posts: 108
Joined: 15 May 2018 21:38
Location: MN
Has thanked: 76 times
Been thanked: 35 times

can we discuss blowback?

Post by stevep1954 »

a fellow lever lover was mentioning blowback when using the 45 colt in his Rossi. does it happen on just levers and why? i am not even sure what it is... thanks
Archer
2000 Shots
2000 Shots
Posts: 3942
Joined: 04 Feb 2014 05:30
Location: SoCal Loco
Has thanked: 137 times
Been thanked: 610 times

Re: can we discuss blowback?

Post by Archer »

Blowback is a term I have not heard applied to lever actions.

I am going to make an assumption here that 'blowback' in this case is referring to combustion gases escaping past the brass and coming toward the shooter.
It is possible that a lightly loaded round may not expand the brass enough to form a gas seal in ANY firearm.

I have NOT experienced this with ANY of my lever actions and I probably own a dozen.
I do not however own a .45 Colt and I do not as a rule run light loads through the lever actions.

.45 Colt is a round that is often loaded quite lightly for Cowboy Action or other light plinking. .45 Colt brass is available today in a thicker hardened brass that can be used for magnum level loads and may require annealing for use with light .45 Colt loads. Failure to anneal the brass while using it for light loads may not give you the proper gas seal. The Rossi chambers are sometimes a bit generous and combined with a light load common with .45 Colt might not give you the gas seal you would want. Combine all these factors and you are more likely to have a problem.

I did do a search on the topic with specific reference to the Rossi 92 and I got this thread off another board:
https://www.thehighroad.org/index.php?t ... es.485157/
(I will note with regards to the end of the conversation that while names may be trademarked patents are specifically not applicable to dimensions alone at least in today's world. Something that came out in the ParaOrd wide body 1911 patent case. I will also note that .44-40 was potentially loaded a bit hotter than .45 Colt and that there was specifically a 1892 ONLY loading available from Winchester.)
Ohio3Wheels
1000 Shots
1000 Shots
Posts: 1599
Joined: 31 Jul 2014 15:18
Location: Dayton Oh
Has thanked: 227 times
Been thanked: 328 times

Re: can we discuss blowback?

Post by Ohio3Wheels »

I have found during load development for my 45 Colt '92 that the low starting loads often result in smokey cases and some powders Titegroup in particular never seem to develop sufficient case expansion to totally seal the chamber before reaching maximum load. As Archer noted some or all of this may be related to case metallurgy.

Make smoke,
Curt... makin' smoke and raising my carbon foot print one cartridge at a time Image
User avatar
Missionary
Founding Member
Founding Member
Posts: 588
Joined: 21 Mar 2012 15:47
Location: Peru
Has thanked: 9 times
Been thanked: 145 times

Re: can we discuss blowback?

Post by Missionary »

Yep.... those minimal charge loads and cases sized to small for a fat chamber will permit gas escape along the brass back towards the bolt.
Cowboy shooters looking for the Edge fire loads that are so low powered a turtle an near out run them.
What purpose those loads have is beyond me.
But you can anneal the neck area of the brass if you want to at sneeze your slugs down range.
Way down south in Arequipa, Peru till June 2020.
User avatar
GasGuzzler
Moderator
Moderator
Posts: 2745
Joined: 02 Nov 2015 19:54
Location: Cooke County, TX
Has thanked: 310 times
Been thanked: 451 times

Re: can we discuss blowback?

Post by GasGuzzler »

Missionary wrote:Cowboy shooters looking for the Edge fire loads that are so low powered a turtle an near out run them.
What purpose those loads have is beyond me.
Same here. I bought some .45 Colt brass from a local guy and he tried to pawn some Trail Boss off on me. :lol:
__________________________________________________________________________________________
I've always been crazy but it's kept me from going insane.
Post Reply