I just had to try them out and I am now workin on some loads for them after special ordering my case trimmer from LEE for this specific round I am ready to turn them out and see if they perform.I have some accurate #9 and according to the hornady ublished info that will push these to1650 at max with 13.5 grains of powder. Anyone else try these yet I know most will say just use the 158grain XTP I have these and shoot them often but they don't look as good as these pointy little devils. LoL This round is not at max as I will work up to that but at 13.7 grains I am hopin she will perform well time will tell I am only startin with 20 rounds at this point to see.
Hornady FTX 140 grain .357 mag bullets
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
-
- Posts: 1
- Joined: 14 Apr 2012 08:41
Re: Hornady FTX 140 grain .357 mag bullets
good for you for working up your loads. you may try to drill out your bullet seating stem to avoid the flext tip polymer from getting deformed. if you have a horandy die you can buy the different bullet seating stem from them made specifically for this bullet. if you have a lee die you can send them a bullet and like $7.50 for a custom stem.
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Hornady FTX 140 grain .357 mag bullets
I was debating drilling a dimple on my seating stem for that reason. I am actaully shocked at how soft the tips are. I think I will just wait and buy one from hornady though thanks for the info didn't know they made one for it.
- Tazman1602
- Posts: 96
- Joined: 04 Nov 2012 06:10
- Location: North Woods of Michigan
- Has thanked: 9 times
- Been thanked: 4 times
Re: Hornady FTX 140 grain .357 mag bullets
AK did you ever use the 140 grain FTX bullets? I just made the major mistake of picking up two boxes of these and then found out I had to trim the brass back in order to use them -- stupid on my part as that is a big pain in the wazoo. I do have some used brass I *might* trim back but geez Hornady that is bad.
I'm a 45-70 shooter and KNOW better than to think a leverevolution bullet would fit a normal sized case. Just wondering how they worked out for you.
Art
I'm a 45-70 shooter and KNOW better than to think a leverevolution bullet would fit a normal sized case. Just wondering how they worked out for you.
Art
Pappys Rifle Shop
Alanson, MI
"A man who is good enough to shed his blood for the country is good enough to be given a square deal afterwards. "
---Theodore Roosevelt
Alanson, MI
"A man who is good enough to shed his blood for the country is good enough to be given a square deal afterwards. "
---Theodore Roosevelt
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Hornady FTX 140 grain .357 mag bullets
I haven't had them at the range yet been shoting my 158grain XTP's my pet load for this 92 have yet to test it I need to thoug to get an update on this page. LoL I'm slow at these things though never remember this untila after I am at the range LoL.
- pricedo
- 2000 Shots
- Posts: 2509
- Joined: 31 Jan 2012 10:36
- Location: Dual Citizen (United States & Canada)
- Has thanked: 56 times
- Been thanked: 234 times
Re: Hornady FTX 140 grain .357 mag bullets
They need to be soft and tough to resist deformation in order to prevent mutual ignition of cartridges in tube magazines and yet be resilient enough not to break apart & fall off even in the presence of oils and lubricants.akuser47 wrote:I was debating drilling a dimple on my seating stem for that reason. I am actaully shocked at how soft the tips are. I think I will just wait and buy one from hornady though thanks for the info didn't know they made one for it.
So far I have had no problems with FTX bullets flattening out or falling off in my 45-70 Guide Guns.
The acid test for Northerners will be how they do in really cold weather. Will they remain tough or harden and break apart in the cold under heavy recoil??
LIFE MEMBER - NRA & GOA