Re: The new self-made rear sight...and one more...and the la
Posted: 09 Jan 2021 15:57
The muximum travel is about 4,5 mm. But the comfort hight (more firm) is 3 mm.
Rossi Rifleman
The Forum for the Rossi Enthusiast! This site is not associated with RossiUSA/Braztech nor is RossiUSA/Braztech responsible for this site's content.
https://www.rossi-rifleman.com/
The new self-made rear sight...and one more...and the last
Page 16 of 16
Re: The new self-made rear sight...and one more...and the la
Posted: 29 Jan 2021 00:34
For those who needs safety I can make the rear sight with safety feature. But it will not be adjustable.
Re: The new self-made rear sight...and one more...and the la
Posted: 01 Feb 2021 19:15
That’s a slick set up!
Re: The new self-made rear sight...and one more...and the la
Posted: 13 Feb 2021 14:15
I can also make brass magazine follower and ship it with sight.
Re: The new self-made rear sight...and one more...and the la
Posted: 15 Feb 2021 10:19
I received a blued Vtoran Model 2 sight in the mail last week. Andrew was responsive, accommodating of special requests, and very clear that it might take up to 6 weeks to make the sight and have it travel halfway around the world. It ended up on my doorstep less than 3 weeks after I ordered it.
I'm very happy with my purchase. I still haven't gotten it to the range, but I think I am going to like the ability to adjust the height very quickly. I added some blue loctite to the height screw to firm it up a little since I may be using a lot of the travel to switch between hot 357 hunting loads and subsonic 38 special plinking loads.
I'm very happy with my purchase. I still haven't gotten it to the range, but I think I am going to like the ability to adjust the height very quickly. I added some blue loctite to the height screw to firm it up a little since I may be using a lot of the travel to switch between hot 357 hunting loads and subsonic 38 special plinking loads.
Re: The new self-made rear sight...and one more...and the la
Posted: 28 Feb 2021 20:02
Andrew you are an artist! What is the procedure for placing an order! Does each sight have an identifying number? They are all works of art.
Thanks
Jay
Thanks
Jay
Re: The new self-made rear sight...and one more...and the la
Posted: 01 Mar 2021 00:28
I was thinking about the numbers, but sights are too small to place it.
If you need the sight just write me PM.
If you need the sight just write me PM.
Re: The new self-made rear sight...and one more...and the la
Posted: 01 Mar 2021 23:19
Gotta tell ya...I really like vtoran's rear sight. His work is very, very good. Delivery took a while, but that was expected. Easy to adjust elevation for differing handloads, and it stays put. No windage adjustment possible for this rear sight, so windage adjustment was via front sight, and done only once! The only modification that I need to make due to my eyesight...is while using a 1/6" bead front sight I may have to open up the rear aperture from 1.5 mm (.059) to 2 mm (.078) for a better sight picture.
Also, I may even round off the outer profile of the rear sight aperture to enhance target acquisition and make it look sexy.
Also, I may even round off the outer profile of the rear sight aperture to enhance target acquisition and make it look sexy.
Re: The new self-made rear sight...and one more...and the la
Posted: 21 May 2021 17:09
These look great.
I'm REALLY hoping his Model 2 sight will work with my standard/OEM front sight (Rossi 92-38/357). If anything, I figure I might need a medium to large aperture.
QUESTION:
Does anyone know if his rear sight will see over a Skinner rail? I assume it will, as someone mentioned it was a low rail.
I'm REALLY hoping his Model 2 sight will work with my standard/OEM front sight (Rossi 92-38/357). If anything, I figure I might need a medium to large aperture.
QUESTION:
Does anyone know if his rear sight will see over a Skinner rail? I assume it will, as someone mentioned it was a low rail.