Lyman 429667 from Western Bullet Company

Extend your shooting experience while reducing the cost of your ammunition!

Re: Lyman 429667 from Western Bullet Company

Postby Arroyoshark » 25 Apr 2022 18:49

Handsome lookin' six-shooter, Sarge, and a nice lookin' bullet. Be a swell trail kit out in the Southwest for sure. A 255 grain bullet moving at nearly 900 fps is no slouch. Should deck black tailed jacks, coyotes and deer with equal success. Stepping that load up to even 1,100 fps would be adequate for hunting black bear at sub-70 yard distance.

That is a good knee supported group way out at 100 yds. You've got a good shooter there.
When sitting down to clean a gun, the first step is to load another gun - Elmer Keith
User avatar
Arroyoshark
 
Posts: 247
Joined: 03 Sep 2012
Has thanked: 12 times
Been thanked: 69 times
My Rossi Choice: M92
Location: fin del sendero, New Mexico

Re: Lyman 429667 from Western Bullet Company

Postby Mad Trapper » 25 Apr 2022 18:59

The .434 cylinder throats are not causing any problems.
That is good shootin.
If you get the mold and cast your own, you could try them sized at .431.
User avatar
Mad Trapper
500 Shots
500 Shots
 
Posts: 507
Joined: 03 Aug 2013
Has thanked: 154 times
Been thanked: 136 times
My Rossi Choice: M92
Location: Daniel Boone Forest

Re: Lyman 429667 from Western Bullet Company

Postby Sarge » 25 Apr 2022 20:51

Thanks guys. I tried to order these at .431" and was told Western only sizes them .430". Reading up on this Lyman mold indicates it tends to cast on the small side, which might explain that. As it worked out, the .430" shoots fine in this revolver.

I'll reserve the 429667 for 44 Special level loads. For my hunting load in this revolver, I've been using the 240 XTP at about 1350. With jacketed bullet shortages and price increases, I'll switch to a 250-260 grain ogival wadcutter, RD or LBT powered to 1100 or so by 4227 or HS6.
Sarge
250 Shots
250 Shots
 
Posts: 263
Joined: 23 Mar 2014
Has thanked: 98 times
Been thanked: 118 times
My Rossi Choice: M92
Location: US

Re: Lyman 429667 from Western Bullet Company

Postby Mad Trapper » 26 Apr 2022 08:22

If you wanted, you could beagle the mold.
Ive done this with an ideal .457 round ball mold to get more accuracy in my 45-70 when making up small game loads.

http://www.castpics.net/subsite2/MoldMods/BDE.pdf
User avatar
Mad Trapper
500 Shots
500 Shots
 
Posts: 507
Joined: 03 Aug 2013
Has thanked: 154 times
Been thanked: 136 times
My Rossi Choice: M92
Location: Daniel Boone Forest

Re: Lyman 429667 from Western Bullet Company

Postby Sarge » 26 Apr 2022 17:55

Since the bullet was flying straight for 100 yards and cutting nice clean holes, I decided to see how it would do with a little turbulence. I sat three one-gallon jugs in a row and behind each, slipped in a scrap of 3/8 plywood. The fourth and last jug was backed an inch and a half of old, wet phone book. Behind those was another scrap of 1/2" plywood, a saw block and a steel plate in case anything got away.

Image

I backed off about 12 feet, sat down on a bucket and held carefully the first jug. I am pleased to report I did not miss, but I did get a little wet. Turns out a 255 grain RNFP trundling along at 860 fps generates a little more mojo than the internet-at-large would have you believe. The bullet bored straight and true through the center of all four jugs, the plywood scraps, the phone book and pert near broke through 1/2" plywood behind it.

Image

It mashed out a bit on the way through. I deem the load trustworthy for general use.

Image
Sarge
250 Shots
250 Shots
 
Posts: 263
Joined: 23 Mar 2014
Has thanked: 98 times
Been thanked: 118 times
My Rossi Choice: M92
Location: US

Re: Lyman 429667 from Western Bullet Company

Postby Mad Trapper » 26 Apr 2022 18:42

more then enough penetration.
People,internet,gun writers dont understand what a big slow bullet with a decent meplat can do, Elmer Keith proved that.
User avatar
Mad Trapper
500 Shots
500 Shots
 
Posts: 507
Joined: 03 Aug 2013
Has thanked: 154 times
Been thanked: 136 times
My Rossi Choice: M92
Location: Daniel Boone Forest

Re: Lyman 429667 from Western Bullet Company

Postby Arroyoshark » 26 May 2022 21:23

That's a pretty impressive test, Sarge. The bullet had some momentum going. I wonder what the result would have been if your jugs were set at around 25 yards. Might demonstrate its hunting capability. I seem to recall writer, Brian Pearce, once writing that he had taken black bear with .44 special and flat point cast bullet with similar velocity at around 50 yds.
When sitting down to clean a gun, the first step is to load another gun - Elmer Keith
User avatar
Arroyoshark
 
Posts: 247
Joined: 03 Sep 2012
Has thanked: 12 times
Been thanked: 69 times
My Rossi Choice: M92
Location: fin del sendero, New Mexico

Previous

Return to Handloading

Who is online

Users browsing this forum: No registered users and 2 guests