Light firing pin strikes, faliure to fire
- Tuco Ramirez
- 500 Shots
- Posts: 859
- Joined: 08 Apr 2013 10:50
- Location: Fredericksburg TX
- Has thanked: 70 times
- Been thanked: 99 times
Re: Light firing pin strikes, faliure to fire
I tossed mine before I went one piece firing pin. Give it a try...
- mr surveyor
- 1000 Shots
- Posts: 1611
- Joined: 16 Mar 2013 11:20
- Location: NE Texas
- Has thanked: 490 times
- Been thanked: 295 times
Re: Light firing pin strikes, faliure to fire
I'm curious .... do the ejectors on the RG's have the same type profile at the 92? .... as it the ejector has the extended "wings" that seat into slots below the chamber throat?
I noticed that after I reshaped the "wings" of the ejector on my 92 that the bolt closed smooth and evenly. Prior to that I could see the bolt face appeared to be pulling down a bit as well as being a bit hard to close.
May not even be similar in design, but just thought I'd throw that out there just so I could leave my unsolicited mark on another thread
JD
I noticed that after I reshaped the "wings" of the ejector on my 92 that the bolt closed smooth and evenly. Prior to that I could see the bolt face appeared to be pulling down a bit as well as being a bit hard to close.
May not even be similar in design, but just thought I'd throw that out there just so I could leave my unsolicited mark on another thread
JD
-----------------------------------------------------------------------------------------
Guns - They aren't really yours until you void the warranty!
Guns - They aren't really yours until you void the warranty!
- Tuco Ramirez
- 500 Shots
- Posts: 859
- Joined: 08 Apr 2013 10:50
- Location: Fredericksburg TX
- Has thanked: 70 times
- Been thanked: 99 times
Re: Light firing pin strikes, faliure to fire
I don't have a 92 but I am sure it is nothing like the Marlin 336 action.
Re: Light firing pin strikes, faliure to fire
OK, so back to the drawing board. Light strikes have gone to less than 2 in ten. Tonight I worked on the bolt so that I now have 26 thousandths clearance on both sides of the hammer and the bolt. The hammer nose was also colliding with the top of the bolt. Lots of filing going on there. The hammer now pushes the firing pin all the way in to the spent primer that I used. Got to get some dummies (other than me). Will get back to you next range session .
- akuser47
- Founding Member
- Posts: 5070
- Joined: 12 Feb 2012 11:43
- Location: ohio
- Has thanked: 1266 times
- Been thanked: 482 times
Re: Light firing pin strikes, faliure to fire
Sounds good also a siuggestion if hammer seating is sloopy in the reciever it may help to shim it to get better alignment I have done this to other guns the the hammer was sloppy in and it solved the misfires
- Tuco Ramirez
- 500 Shots
- Posts: 859
- Joined: 08 Apr 2013 10:50
- Location: Fredericksburg TX
- Has thanked: 70 times
- Been thanked: 99 times
Re: Light firing pin strikes, faliure to fire
Sounds like your on the right path.... Keep us posted.
Re: Light firing pin strikes, faliure to fire
Well the RG fired all but the last round. When I ejected it the pin strike was almost beside the primer. So it appears that when in battery, the bolt somehow moves around in the receiver. So stronger spring, and all the touch up isn't going to remedy that. Back the shop.
- Tuco Ramirez
- 500 Shots
- Posts: 859
- Joined: 08 Apr 2013 10:50
- Location: Fredericksburg TX
- Has thanked: 70 times
- Been thanked: 99 times
Re: Light firing pin strikes, faliure to fire
With the bolt out on mine I noticed there was little room for error seating the case into the bolt face. The side walls on the bolt face were square. I tapered ever so slightly the inside wall on the bolt face to help guide the case into the face. I'm at work so I can't send a pic hope you understand what I am referring too.
I also dressed up the extractor hook because it seemed way to long. Now that I think about I have worked on just about every part in the rifle..... Trust me when I say I was not laughing when I was have FTF issues.
I also dressed up the extractor hook because it seemed way to long. Now that I think about I have worked on just about every part in the rifle..... Trust me when I say I was not laughing when I was have FTF issues.
-
- 1000 Shots
- Posts: 1650
- Joined: 03 May 2013 10:14
- Location: LaGrange Georgia
- Has thanked: 7 times
- Been thanked: 341 times
Re: Light firing pin strikes, faliure to fire
ozarki wrote:Well the RG fired all but the last round. When I ejected it the pin strike was almost beside the primer. So it appears that when in battery, the bolt somehow moves around in the receiver. So stronger spring, and all the touch up isn't going to remedy that. Back the shop.
That's what I was talking about earlier. The top of the bolt face, does not have a "rim" to keep the boltface and case head in alignment. That's why I wanted to weld something in the receiver to hold the bolt UP in the correct position.
I wonder if maybe rossi cut too much metal out of the receiver and that's why the bolt is not supported in the proper position. Wish I had a marlin to compare it to.
Don Huff
to bad those that know it all, cant do it all!
16" SS 92 357
20" BL 92 357
20" SS 92 44
20" BL 92 44
20" Bl 92 45C
20" Bl 92 454
SS Rio Grande 30-30
Bl Rio Grande 45-70
to bad those that know it all, cant do it all!
16" SS 92 357
20" BL 92 357
20" SS 92 44
20" BL 92 44
20" Bl 92 45C
20" Bl 92 454
SS Rio Grande 30-30
Bl Rio Grande 45-70
Re: Light firing pin strikes, faliure to fire
Went to the shop when I left you last night. Pulled the lever and bolt from my RG-4570. Apparently the only thing that keeps the bolt square with the receiver is the extractor and the ejector. I haven't paid much attention to the receiver/barrel junction, but should have. The groove the rim of the cartridge lays in is very shallow. My FTF the other day was caused by a loose extractor and a pile of 5744 jammed into the shallow groove, holding the cartridge out of the shallow groove causing the pin strike to almost miss the primer. I'm through with 5744, way too much unburned powder, and this is with a good solid crimp.
I don't expect this to solve the FTF problems on anyone elses RG but a rather strange situation of mine alone. When it stops raining I'll get to the range for more testing. As an aside, I now have 10 cartridges marked to index, so will know where the pin strikes are from 12:00. Should have done this weeks ago
Wes
I don't expect this to solve the FTF problems on anyone elses RG but a rather strange situation of mine alone. When it stops raining I'll get to the range for more testing. As an aside, I now have 10 cartridges marked to index, so will know where the pin strikes are from 12:00. Should have done this weeks ago
Wes